Wolverine Soffit and Decorative Trim Manual de usuario descargar pdf (Pagina 49)

Creating End Caps for 5" Lineals

To create the header, first cut a 7" piece of 5" lineal. Measure

and trim as shown.

The resulting piece fits into the end of the 5" lineal.

The ends of the 5" lineal also need trimming to receive the end

caps. Create a 3/4" rain tab in the pocket area and trim off a

3/4" tab from the bottom.

NOTE: To make end caps for 3-1/2" lineals, simply start

with a 5-1/2" piece and remove the 3/4" and 2" areas as

shown for the 5" end caps.

Wolverine Fit and Finish Installation Guide

3/4"

rain tab

remove

1 2 ... 44 45 46 47 48 49 50 51 52 53 54 ... 116 117

Fit and Finish 1
Installation Guide 1
Important Information 2
888-838-8100 3
Become a Wolverine 3
Master Craftsman 3
TABLE OF CONTENTS 4
SECTION 1 6
Siding Terms 7
Starter Strips 8
Corner Starter Strip 9
J-channels and F-channels 10
Utility Trim 11
Miscellaneous Accessories 12
Lineal Options 13
Cornerposts 14
Equipment and Tools 15
Tools Required 16
Ladders and scaffolds 16
Cutting table 16
Portable brake 16
Special Tools 17
SECTION 3 – Estimating 18
Upper wall of gambrel house 19
Dormer sides 19
Porch Ceiling 19
Measuring 20
Estimating Form 21
Preparing Wall Surfaces 22
Applying over stucco 24
Applying over steel studs 24
Nailing, Stapling and 25
Other Fastening Methods 25
Other fastening techniques: 26
Power screwdrivers 26
Pneumatic staplers/nailers 26
Expansion and Contraction 27
Installing Accessories 27
Installing the starter strip 28
Capping an outside cornerpost 30
Extra Wide Corner Posts 31
(Four-Piece Corner System) 31
Inside Cornerposts 32
Federal Corners 33
Inside Federal Corners 34
Trimming Bay Window Corners 35
Decorative Trim Options 36
Window Flashing 37
To Square Cut Corners 38
To Miter Cut Corners 38
Drip Clip 39
Lineals and Decorative Trim 39
Windows and Doors 40
Corner blocks 41
Crown molding 41
Windows and Door Surrounds 42
Blind Miter 46
Corner Blocks 47
Option 1 (page 51) 51
Option 2 (page 51) 51
Option 3 (page 52) 51
Crown Molding and Cap for 52
3/4" Pocket J-channel 52
Crown Molding with 52
3-1/2" Lineal Surround 52
Crown Molding with Cap for 53
5" Header Lineal 53
Using Lineals as Gable Trim 56
Cutting Panels 57
Overlapping Panels 57
Installing remaining courses 59
Fitting under windows 59
Install panel 59
24" 61
16" 61
Installing trim at roof line 62
Fitting at gable ends 62
Fitting under soffit 63
Completion 64
Shutter Installation 65
Installing Cornerposts 67
If using J-channel 68
Plan the panel layout 69
Important! 69
Installing Wall Panels 70
Installing Gable End Panels 71
Porch Ceilings 73
Remodeling Projects 74
Installation over Open Eaves 75
Installing Soffit 76
Turning a Corner 76
Completing the Installation 76
InvisiVent Soffit 78
Installations without soffit 79
Aluminum fascia 80
Important 81
First course 82
29" 83
Finishing the top course 84
Installing Mitered Cornerpost 84
Installing Cornice Cap 84
Installation 85
Second course 87
Half-Rounds in Gable Ends 89
Hanging the starter course 90
Installing first full panel 91
Lapping remaining panels 91
Installing the last round 91
Starting Half-Rounds 93
MADE IN USA 95
(Option 1) 96
Preparing the new panel 97
Installing the new panel 98
Shapes Panel (Option 2) 100
Random Hand-Split Shakes 101
To finish the top course 103
Installing Millennium 104
Fastening 105
Panel Lock 105
Non-Horizontal Applications 106
Removing Panels 106
Installing TrueComfort 107
Around windows and doors 108
Under soffit 108
Overlapping panels 108
Trimming Curved Openings 109
Frieze Board 110
Decorative Sunbursts 110
SECTION 10 – Repair 113
SECTION 11 – Miscellaneous 115
Siding over Asbestos 116
Historic Restoration 116
For More Information 117

Comentarios a estos manuales

Sin comentarios

Wolverine Soffit and Decorative Trim Manual de usuario Pagina 49

Comentarios a estos manuales